Make sure that the file-id specified in your DLBL statement meets the criteria for a valid VSAM file-id. Programmer Respone: Do one of the following: Correct the problem that caused the preceding catalog recovery operation to fail. This may be done by specifying the number of tracks and blocks in the EXTENT statement or by specifying RECORDS and RECSIZE on the DLBL statement for device independent allocation. X'06' 006 Return Code=04 Action=CBMN The SHOWCB or TESTCB OBJECT operand refers to a non-esistent index. have a peek here
PROGRAMMER ACTION: Request a programmer logical unit that was specified at system generation. Indicates a boundary violation. Use this when there is RC 12 in vsam-extended-return-code 004 Read error on data 008 Read error on index 012 Read error in sequence set 016 Write error on data Ensure that the operator mounts the correct volume.
X'04' 004 Return Code=>0 Action=CLOSE The ACB was already closed. To use simplified job control, eliminate EXTENT statements and ASSGN statements describing your VSAM clusters. Rerun the job after the system problem is corrected. PROGRAMMER ACTION: Depends on the processing done during the preceding run.
Return Code=08 Action=OPEN Addressed or control-interval insertion is requested for a key-sequenced or relative-record file. The operand must be specified. PROGRAMMER ACTION: Rerun the job in a large partition. Vsam File Status 16 In Easytrieve The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than expected, or an I/O error.
Possible causes for this error code are: An attempt to get virtual storage failed An I/0 error occurred while VSAM was reading the VTOC An extent block is not availabe in Vsam Feedback Codes This will not restrict files that use a max-CA for the control area size. Use Access Method Services EXPORTRA command to export the file for subsequent reimportation. X'94' 148 Return Code=08 Action=OPEN No valid entry was found in the catalog for the ACB to be opened or for the alternate index structure related to this ACB.
CONDITION CODE IS 12 Resolution The DADSM CREATE Diagnostic info x'040343C9' means "SMS managed volumes specified for non-SMS request". Vsam Status 23 Rerun your job. Instruct the operator to ensure that the device on which the volume mounting is done is in "up" status and unreserved before replying `NEWPAC'. PROGRAMMER ACTION: Use Appendix B to determine the cause of the error in message 4A371 and take the recommended corrective action.
If circumstances indicate that no more extent blocks are available, rerun the job together with other jobs that require a smaller number of extent blocks (in a multiprogramming environment), or restructure The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than that expected, or an I/O error. Vsam Return Code 28 X'8C' 140 Return Code=08 Action=Request VSAM encountered an inconsistent spanned record (that is, one or more segments were incompletely updated to destroyed). Vsam Extended Return Code Can Contain The Message Rerun the job.
If the request was a GET, the record (or as much of it as possible) was moved to the user's work area. http://chatflow.net/return-code/vsam-repro-return-code-28.html Return Code=08 Action=Request As many requests are active as the number specified in the STRNO = n operand for the ACB or BLDVRP macro; therefore, another request cannot be started. For recoverable catalogs, VSAM always assigns a programmer logical unit for each CRA. The last I/O statement executed for the file, before the execution of a DELETE or REWRITE statement, was not a READ statement. 44 A boundary violation exists. Vsam Return Code 16
X'07' 007 Return Code=04 Action=CBMN The referenced EXLST does not contain an entry for the exit you specified in M0DCB or SHOWCB. Rerun the job. PROGRAMMER ACTION: Have your program executed in a larger virtual partition. Check This Out Return Code=08 Action=Request An invalid RBA has been specified.
Note:A SimoTime License is required for the items to be made available on a local system or server. Vsam Return Code 168 X'D8' 216 Return Code=08 Action=OPEN ACB MACRF = LSR (local shared resources) is specified, but the key length of the file being opened is greater than the maximum key length specified X'1C' 028 Return Code=00 Action=Request The record retrieved by a GET-with-no-updata may be a duplicate of a record in another CI.
PROGRAMMER ACTION: Specify ACB MACRF = NUB (no user buffers) of ACB MACRF = CNV (control interval access). Therefore, adjustments may be needed to execute the jobs and programs when transferred to a system of a different architecture or configuration. An error may have occurred during lock Manager processing. Vsam Open Return Code Is 232 The combinations of possible values and their meanings are shown below with some comments where vendor additions or extensions may occur.
An attempt was made to access a relative-record file with an access type other then keyed or control interval. Enter your email address here Advertisement Home About Me Sitemap Contact Me Copyright © 2016 Rui Miguel Feio Send to Email Address Your Name Your Email Address Cancel Post was not Return Code=00 Action=Request VSAM detected an end-of-volume condition. this contact form PROGRAMMER ACTION: Changes the device address in the ASSGN statement to that of the VSAM volume being opened.
PROGRAMMER ACTION: If data integrity problem arise, revert to a valid backup copy of the file. Return Code=08 Action=Request The maximum number of pointers in the alterenate index has been exceeded. Return Code=08 Action=OPEN The ACB to be opened is already being used. Return Code=08 Action=OPEN This ACB is already opened.
X'54' 084 Return Code=08 Action=Request Locate mode was specified for a PUT request of for processing in a user buffer. To use simplifed job control, eliminate EXTENT statement and ASSGN statement describing your VSAM clusters. To assist in problem diagnosis, you might wish to run a SNAP dump 0001, as described in the "Diagnosis Aids" section of VSE/VSAM/VSAM logic, Volume 1 or Volume 2. This code can be issued for a file being accessed through a path if the pointer to the record is missing from the alternate index.
Managed-SAM will simulate the open of an empty file for DTFSD TYPEFLE=INPUT requests. Return Code=08 Action=OPEN The OPEN disposition specified for the file conflicts with other files characteristics. SimoTime Technologies makes no warranty or representations about the suitability of the software, documentation or learning material for any purpose. PROGRAMMER ACTION: Changes the device address in the ASSGN statement to that of the VSAM volume being opened.
It was altered via the ALTER command with the INHIBIT option. Return Code=08 Action=Request VSAM encountered end of file (during sequential retrieval), or the search argument is greater than the highest existing key (or relative record number) in the file. Return Code=08 Action=Request The requested record is contained in a control interval that is already held in exclusive control by another request. This is probably a system error.
PROGRAMMER ACTION: Retry. Return Code=08 Action=Request VSAM could not obtain a sufficiently large contiguous area of virtual storage. System Action: Close processing continues to successful completion, assuming no other complications. I think you need to reset the password and try running the job again.